英國TTi PLH120P/PLH250P高可編程直流穩壓電源

PLH-P系列是TTI新的線性穩壓電源系列總線可編程版本。

PLH-P系列包括所有的PLH系列手動控制的功能，但增加了全面的遠程控制功能。

超緊湊型架模塊尺寸使得它非常適合安裝在機架上的應用系統，而用戶友好的手動控制保留臺式應用程序。

為了滿足今天的工程師們的不同需求，提供一系列的接口。RS-232接口，USB和LAN（以太網）與LXI支持提供標準。

每個數字總線接口提供的電壓，電流控制，輸出開/關，加回讀電壓，電流和地位。

產品特點：

高性能的線性穩壓電源

全數字化遠程控制和讀出

RS-232接口，USB和LAN（以太網）

LAN接口符合LXI標準

可選的GPIB接口

接口的光電隔離輸出

IVI驅動器提供

隔離的模擬遙控V和我

簡單的主從式并行布線模擬輸出

季度架3U超緊湊的尺寸

高功率密度達94瓦特輸出

根據英國系列手動控制功能

產品型號/規格：

PLH120-P - 0 to 120V at 0 to 750mA
PLH250-P - 0 to 250V at 0 to 375mA

Lower Voltage Models - Go Here for New PL and PL-P Series

PL068-P - 0 to 6V at 0.to 8A
PL155-P - 0 to 15V at 0 to 5A
PL303-P - 0 to 30V at 0 to 3A
PL601-P -  0 to 60V at 0 to 1.5A
PL303QMD-P - 2 x (0 to 30V at 0 to 3A)
PL303QMT-P - 2 x (0 to 30V at 0 to 3A) plus 0 to 6V at 0.to 8A

Digital Bus Interfaces - RS-232, USB, LAN (LXI)

Full remote control and read-back using RS-232, USB or LAN (LXI-C). All interfaces are at ground potential and opto-isolated from the outputs.

Note: Remote/Local Sense is manually selectable only.

RS-232

Standard 9-pin D connector. Baud rate 19,200 max.

USB

Standard USB hardware connection. Operates as a virtual COM port.

Ethernet (LAN)

Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol for connection to Local Area Network or direct connection to a single PC.

GPIB (only with Option G)

The interface conforms with IEEE-488.1 and IEEE-488.2.

LXI Compliance

LAN interface is compliant with LXI-C. (LXI is the abbreviation for Lan eXtensions for Instrumentation).

Digital Programming Performance

Voltage Setting

Setting Resolution: 10mV
Setting Accuracy: ? (0.1% +50mV)

Current Setting

Setting Resolution: 0.1mA (0.01mA on 75mA range)
Setting Accuracy: ? (0.3% +0.3mA); ? (0.3% +0.03mA) on 75mA range

Programming Speed

Command Delay: Typically <80ms (this must be added to any of the figures below)
Voltage Up Time: Typically <45ms* to 1%
Voltage Down Time: Typically <20ms* to 1% (full load); typically <150ms* to 1% (no load)

* The up and down times vary with model, current range and voltage step size. More information is contained in the operating manual which can be downloaded from our web site.

Analog Remote Control

Isolated analog voltage control of voltage and current. Analog control outputs are also provided to enable easy parallel connection of multiple units in a master-slave configuration.

Scaling

Set Voltage Input: 0V to 10V sets 0 to 100% of rated output (e.g. 0 to 120V for PLH120-P).
  Alternative scaling of 0V to 5V (selectable using internal link).
Set Current Input: 0V to 10V sets 0 to 100% of rated output (e.g. 0 to 750mA for PLH120-P).
  Alternative scaling of 0V to 5V (selectable using internal link).
Reference Point for control outputs: control output voltage are referenced to the positive output terminal
Voltage Output: 0 to 100% of rated output voltage generates 0V to 5V.
Current Output: 0 to 100% of rated output current generates 0V to 5V.

Accuracy

Set Voltage Input: +/- (0.3% +100mV); Input Impedance = 10kOhm
Set Current Input: +/- (0.5% +0.5mA); Input Impedance = 10kOhm

Voltage Output: +/- (0.3% +100mV); Output Impedance = 125Ohm
Current Output: +/- (0.5% +0.5mA); +/- (0.5% +0.5mA) on 500mA range; Output Impedance = 125Ohm

Remote Analog On/Off Control

Non-isolated terminal which sets the output to Off when pulled low by gate signal or relay closure. Signal is reference to the positive output terminal.
Note that the PL303QMD-P does not have this facility.

Rear Terminals

Power connections are duplicated on the rear panel using a screw-less connector block.
Digital Bus Interfaces - RS-232, USB, LAN (LXI)

NOTE: The above specifications are additional to the Manual Control specifications which can be seen Here.

GENERAL SPECIFICATIONS

Input

AC Input: 230V AC or 115V AC +/- 10%, 50/60Hz. Installation Category II
Input Power:  280VA max.

Temperature & Environmental

Operating Range: +5oC to +40oC, 20% to 80% RH
Storage Range: -40oC to + 70oC
Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2.
Cooling: Intelligent variable-speed low noise fan assists convection.

Safety & EMC

Safety: Complies with EN61010-1
EMC: Complies with EN61326

Physical

Size: 107mm x 131mm (1/4 rack 3U) x 315mm,
(sizes exclude feet, knobs and terminals).
Weight:  4.55kg (10lb);

DRIVER SOFTWARE SUPPLIED

IVI Driver

An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows*, HPVEE* etc.

USB Driver

An installation file is supplied which calls a standard Windows* USB driver.

* LabView and LabWindows are trademarks of National Instruments. HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. * USB interface is supported for Windows 98-SE, 2000, XP, Vista and Window 8 (including 64bit versions). Windows is a trademark of Microsoft.

OPTIONS

Rack Mount (RM450)

19 inch 4U rack mount suitable for up to four single power supplies, two dual power supplies, or any mixture. Blanking plates are provided for unused positions. The 4U height provides limited ventilation space above and below the power supplies.

Option G

Adds a GPIB (IEEE-488) interface.
This is in addition to the RS-232, USB and LAN interfaces of the standard PLH-P product.